Description of Services Engineering: Engineering consists of: * But is not limited to Preliminary site visits, with the customer, to determine the project needs. Equipment, battery and cable sizing calculations, for present site requirements, with growth over-build, per the customers’ needs. Drafting a project specific scope of work (SOW) and method of procedure (MOP) for each task to be performed. Periodic site visits for quality control and progress reporting. Represent the interests of the customer, on-site, during all planning stages of on-going new construction or existing build-out projects. Assist the customer in site selection based on location and building accessibility. (Both physically for equipment installation and logistically for connection to existing transmission lines.) Engineer the most fail-safe methods for keeping revenue-generating equipment "on-line". (This would apply in the design, installation and connection to, all electrical systems.). Design power rooms to serve present load requirements as well as future growth, at a rate of approximately fifteen percent (15%) growth, per year. Consult with different equipment manufacturers about their newest equipment designs and select the equipment that will provide : a) Optimum performance, b) Cost effectiveness, c) Expansion capabilities and d) Warranty/Service Agreement Insure the most cost effective and timely installations by working directly with the Architectural/Engineering firms, as a customer representative Assist in the selection of contractors to perform the electrical installations. Support the customers’ implementation team with timely progress reports for each project. Oversee the installations with site visits to assure that all time-lines are met. Provide an upgraded growth path to newer technology. Remedial Service: Remedial Service consists of: * But is not limited to Any corrective-action service required for maintaining or repairing existing equipment. Remedial service calls have a maximum response interval of 24 hours. Constant Current, per availability from the equipment manufacturer will supply any and all parts needed for remedial service.   (Constant Current will assume no responsibility for any data, revenue, and labor or equipment losses due to the unavailability of parts.) Preventive Maintenance For Batteries, Rectifiers and DC Power Plants: Preventive Maintenance consists of annual, semi-annual or monthly DC plant survey and testing. The breakdown of services provided with each are as follows: BATTERY PLANT MAINTENANCE BI-MONTHLY SEMI-ANNUAL ANNUAL BY REQUEST Check general appearance and cleanliness YES YES YES YES Check cells for cracks or electrolyte leaks YES YES YES YES Check inter-cell busses for corrosion YES YES YES YES Check connections and re-torque BCR YES YES YES Check electrolyte levels * YES YES YES YES Check felt pads * YES YES YES YES Check ambient temperature and ventilation YES YES YES YES Check integrity of battery racks YES YES YES YES Measure electrolyte temperature @ pilot cell * YES YES YES YES Measure specific-gravity @ pilot cell * YES YES YES YES Measure specific-gravity of all cells * BCR YES YES YES Measure cell voltages of all cells YES YES YES YES Perform termination resistance check NO NO YES YES Battery "Service" dischargetest (w/bldg. load) BCR BCR BCR YES Battery "Performance" discharge test (w/ load-bank) BCR BCR BCR YES Calculate approximate reserve time BCR BCR YES YES (* Wet cell plants only.) BCR-by customer request RECTIFIER PLANT MAINTENANCE BI-MONTHLY SEMI-ANNUAL ANNUAL BY REQUEST Check general appearance and cleanliness YES YES YES YES Check equipment and cable labeling YES YES YES YES Check alarm setup and calibration YES YES YES YES Check meter calibration YES YES YES YES Check parallel operation (load-sharing) YES YES YES YES Check float voltage YES YES YES YES Check equalize voltage YES YES YES YES Check current-limit threshold BCR YES YES YES Check high-voltage-shutdown threshold BCR YES YES YES Check capacitor integrity BCR BCR YES YES Check operation of all breakers BCR BCR YES YES Perform infra-red heat scan BCR BCR BCR YES BCR-by customer request POWERBOARD MAINTENANCE BI-MONTHLY SEMI-ANNUAL ANNUAL BY REQUEST Check general appearance and cleanliness YES YES YES YES Check equipment and cable labeling BCR YES YES YES Check alarm setup and calibration YES YES YES YES Check meter calibration YES YES YES YES Check cable voltage drop to loads BCR BCR YES YES Check existing load vs. capacity of MDB YES YES YES YES Check Low-Voltage-Disconnect setting BCR BCR YES YES Perform infra-red heat scan BCR BCR BCR YES BCR-by customer request